Nissan B13 Restoration

[star2]

That's why she beats me once or twice, and beats me too hard :D. But i would rather give a few loly pops to a stubborn kid rather than buying her a box of imported chocolates

Nice going so far sir, if seen from the eyes of a perfectionist Nissan enthusiast

Thank you man, its surely worth it, though not for everyone

[star2]

updates coming shortly.....

[SER_GTR]

You are right saqib bhai, actually the priority is to only first lay down the wiring harness and put out the old junk wiring so that to start with, we have a good ground. Then, we will install the heater and cooler boxes as those are plug and play with the wiring, and the panel which shows control for them. Nothing complicated. Rest comes later. Primarily my objective is to clean the wiring issues on the basic looms as when I opened up the wiring, there were literally no grips and some of the grips were unknown to me (not of this car) which were attached in very bad way, on a whole wiring was messed up inside out.

Leave The Engine Loom And Fit This Up....Time To Open Dash Board Meanwhile The LOOM Is On Way....Open The Dashboard And Keep It Safe And Be Very Specific With Work Doing....Just Concentrate On This And Make It Work .....!!! The Power Doors And A/C Touch Panel..

Its Mostly A Grip To Grip Bolt-On Just Need To Connect Some Wires If Necessary....!! Won't Be Hectic As You Already Pay The Price From Your Pockets.....!!!

Once You Lay Over This ...You Will Be Just Then Working On LOOM Either Of GA And QG And Blending It With Your New NEW LOOM..

This One Looks GA COmpatiable LOOM SO If All Power COnnections Are There With ECU Grips Also Connected.....Then All You Need Is Plug And Play Nice And Clean

[spectra]

@star2 Listen to Farrukh without asking stupid questions for a change please. That is the only way to go forward.

[star2]

Okay, here are some updates guys.......

Body work has started on the back side and diggi is aligned perfectly.

[star2]

Denting going on of the housing of backlights.....

While on the front side, we are just ready for the base coat......... the ground is prepared after a hardwork of 3 days, each and every detail is considered in the engine bay.....

marvellous work done by the painters here.....

[star2]

Doors are out, soon work is going to start on them, and current doors will be out as soon as back fenders are aligned by denter....

[star2]

Front suspension is all out and will be inspected for any replacement of bushes or parts......

[star2]

This thing I hate the most, the diggi lock housing, it was in very bad shape, I asked denter especially to give it back its original shape and he was like a magician :). It is perfectly aligned back to its original shape now and looking cool. I wish I could get the original plastic liners for it along with carpet

[ZEE82]

Leave The Engine Loom And Fit This Up....Time To Open Dash Board Meanwhile The LOOM Is On Way....Open The Dashboard And Keep It Safe And Be Very Specific With Work Doing....Just Concentrate On This And Make It Work .....!!! The Power Doors And A/C Touch Panel..

Its Mostly A Grip To Grip Bolt-On Just Need To Connect Some Wires If Necessary....!! Won't Be Hectic As You Already Pay The Price From Your Pockets.....!!!

Once You Lay Over This ...You Will Be Just Then Working On LOOM Either Of GA And QG And Blending It With Your New NEW LOOM..

This One Looks GA COmpatiable LOOM SO If All Power COnnections Are There With ECU Grips Also Connected.....Then All You Need Is Plug And Play Nice And Clean

i was about to say this, but u took the lead that its a GA compatiable loom, n wil even connect the ECU of GA in a plug n play way...and after that....everythng realted to the cluster that is CEL, RPM and VSS wire, some others that f blower and headlamps idling control wires..in short all wil start working automatically..but if he puts QG, then he il be compelled to strip off and cut the nessecarry wires one by one

[ZEE82]

[QUOTE=star2;4137932]Okay, here are some updates guys.......

Body work has started on the back side and diggi is aligned perfectly.

allign the right top surface of the diggy with the body as well

[ZEE82]

Denting going on of the housing of backlights.....

While on the front side, we are just ready for the base coat......... the ground is prepared after a hardwork of 3 days, each and every detail is considered in the engine bay.....

marvellous work done by the painters here.....

i must say...hates off to them,u guys and the whole team.reminds me my car going through its operation a month ago but sadly the pics were all lost due to a corrupt mmcard

[ZEE82]

kindly share the pix of the old wiring loom with us.

[IsbCap]

reminds me my car going through its operation a month ago but sadly the pics were all lost due to a corrupt mmcard

I lost the pics of my brother's marriage, but didn't give up, and finally managed to recover them through a recovery software. You can try some software, if that card hasn't been refilled over and over again.

[ZEE82]

I lost the pics of my brother's marriage, but didn't give up, and finally managed to recover them through a recovery software. You can try some software, if that card hasn't been refilled over and over again.

ahan.thats a brilliant idea bro

[IsbCap]

@star2

Really nice and speedy going with the denting painting job. Here in Isb, my father handed over his Kia classic to stupid denter painters, only for painting a front bumper and doors. And it has taken more than two weeks now. You can guess the state of affairs here in Isb.

Time for you to migrate to Isb and open your denting painting shop as well

[margallar]

Where is this workshop? I'd like to visit sometime

Sent from my SGH-T989 using PW Forums mobile app

[syncview]

@star2

i think you didn't get my message today

any progress on the decision of the engine?

[star2]

[QUOTE=star2;4137932]Okay, here are some updates guys.......

Body work has started on the back side and diggi is aligned perfectly.

allign the right top surface of the diggy with the body as well

Everything will be aligned don't worry.... it will be near to flaw less as far as denting is concerned....

[star2]

kindly share the pix of the old wiring loom with us.

Okay Sir, tomorrow will do that.