Daewoo fan club

[testdriver]

Are the rings easily available locally with tire/rim shops ?

Actually you have to consult a rim repair shop, they have free size aluminum rings. They will bore it according to the requirement and fit into the rim.

[Surd80]

Actually you have to consult a rim repair shop, they have free size aluminum rings. They will bore it according to the requirement and fit into the rim.

OK thanks. I am soon going to convert my racer into Cielo. I find information provided i this forum very use full . Plus i want to plan everything in advance before i start the actual conversion.

[mrasifrasool]

[kamranzafar.ch]

I asked the questions because usually when a different compressor is installed, there is no switch in it to tell the ECM that the AC compressor is ON, and the radiator fan starts only when the engine get hot. If the compressor is genuine, then you just have to check the cooling system of the engine. Usually when the AC is switched ON, it is quite normal that the engine temperature rises, still if you feel overheating, then radiator seems to have some problem probably some tubes are blocked within it.

@zeeshan213

Hope you got your answer.

Someone also advised me to flush out the whole AC unit and condenser as AC compressor leakage might cause the AC condenser not to work properly.

I also congratulate you on the double century of this forum. It is indeed a great source of info for any Daewoo lover

[kamranzafar.ch]

r u sure whether your AC's compressor is periodically getting tripped or constantly running??
My engine temperature is remain almost same (at white area) with or without AC ,
REASON:
1-when i run my car without AC , there is no additional load on engine , so Radiator fan keeps engine temperature as low.
2-when i switch on AC , there is additional load on engine so technically it should heatup, so AC condenser fan also starts with AC (2 Fan running at the same time , Radiator and condenser fan) but still engine temperature should rise as compare to AC off. but i got installed another additional fan with AC condenser , so at the same time three fans run which keep the engine temperature at white level. so there is no Radiator water reduction issue.
3-So additional fan is also capable for excellent AC's cooling , although traffic jamming under direct sun in rwp disturbs the AC's cooling (coz car RPM remains at 700 rpm in idling) but engine temperature remains almost low.

I'm sure my AC compressor is constantly running
I also congratulate you on the 2nd century of this forum. Indeed you are a very Worthy contributor on this forum.

How is Asjad Bukhari. Now a days I hardly get any update from him Pay my regards to him and thank you for your interest in this issue

Regards
Kamran

[asad_scorpio21]

I'm sure my AC compressor is constantly running
I also congratulate you on the 2nd century of this forum. Indeed you are a very Worthy contributor on this forum.

How is Asjad Bukhari. Now a days I hardly get any update from him Pay my regards to him and thank you for your interest in this issue

Regards
Kamran

thanks for ur wishes ,
Asjad is fine , by the way how do u know him???

[saadshaukat]

Assalam o alykum!!
Mashallah the DFC is evergreen
@testdriver
I am having persistant Brakes issue, I get them adjusted and balanced, but after sometime(2mnths) the rear drums mess up again...i even met an accident, thanks to rear brakes not working properly...
Costing me new bonnet and 15k in total...I swapped the servo back in 2006 to some kabli...any advice??
Jaza kallah

[saadshaukat]

Please drive ur daewoos safely...this what happened to mine in March

[saadshaukat]

Should I go for manifold, injector rail and box air filter and ECM for GTi... is it worth anything? This for the 1.5 block ...plz give ur feedback?

[kamranzafar.ch]

thanks for ur wishes ,
Asjad is fine , by the way how do u know him???

Sorry Bro for the delayed reply. I was excessively busy in office work. I work in Legendware as during last job Asjad was with me

Kamran

[asad_scorpio21]

Sorry Bro for the delayed reply. I was excessively busy in office work. I work in Legendware as during last job Asjad was with me

Kamran

Oh IC , he is now in Al Jazeera TV ,Doha Qatar .
wat about ur engine heatup issue with AC ,
i was facing the same problem than got cleaned and washed Radiator and AC Condensor under supervision of Mian Khan , so problem was solved.

[SalarsCar]

Aslamualaikum to all Brothers

Our PC based scanning tool is ready! Have a look at the snapshots

Dashboard View of the Scan tool while the vehicle is running at 33 mph

Engine values under idle conditions with AC 'off'

Engine values with AC 'on' , note the difference in IAC values

Voltage levels of sensors during idle running

If any body is interested, I would like to post further details as well. Anyways our "Project # 1" is at final stages. Last few milestones left are:-
a) Active involvement with Daewoo Racers ECM by changing its parameters while the engine is running to test its actuators.
b) To dump the ECMs memory on PC.
c) To permanently change the engine performance parameters (trickiest job:-!)

Plz help me all in doing so. Enjoy this gift for the 200th page.

Khuda e Paman

[testdriver]

Assalam o alykum!!
Mashallah the DFC is evergreen
@testdriver
I am having persistant Brakes issue, I get them adjusted and balanced, but after sometime(2mnths) the rear drums mess up again...i even met an accident, thanks to rear brakes not working properly...
Costing me new bonnet and 15k in total...I swapped the servo back in 2006 to some kabli...any advice??
Jaza kallah

Sorry for the late reply.

Please elaborate "not working properly". Do they 'jam' or 'frees up'? Which servo you have installed? Did the mechanic changed the brake geometry (Diagonal to Straight)?

[testdriver]

Should I go for manifold, injector rail and box air filter and ECM for GTi... is it worth anything? This for the 1.5 block ...plz give ur feedback?

If your TBI is working perfectly, don't go for the 4 injector (MPFI) manifold. You have to replace the ECM along with routing three more wires for Oxygen sensor and IAT from your existing wiring. Then you have to source Oxygen sensor to get perfect tune. In return you will get lower engine noise by 10% thanks to the resonator.

[testdriver]

@SalarsCar

Well done bro!

It was nice meeting you...

[saadshaukat]

Please elaborate "not working properly". Do they 'jam' or 'frees up'? Which servo you have installed? Did the mechanic changed the brake geometry (Diagonal to Straight)?

They neither jam nor free up, the car is moves diagonally when brakes are applied, the Corolla servo is being used perhaps...

[testdriver]

They neither jam nor free up, the car is moves diagonally when brakes are applied, the Corolla servo is being used perhaps...

By design the Daewoo Racer brake geometry is diagonal. The front right wheel and the rear left wheel are engaged first and then the front left and rear right wheel, thanks to the brake proportionate valve designed to work seamlessly according to the brake geometry. When the master cylinder is changed (off some other make car), the geometry also needs to be changed (since the other master cylinder is designed for straight brake geometry) otherwise the car will tend to move towards right/left during braking.

[yousafhussain]

Dear test driver,

Assalm-o-alikum i have purchased a woo in a very low budget the machanic first checked the car its engine is in good condition but it needs some work round about 20k in which i have to do the wiring of ECM because the carborator installed in this car is nissan the engine is daewoo 1600cc and five forward gears now my car is on work shop for some starring work and wiring and also the other accessories like the carborator and its sensors and wiring now what you suggest the nissan carborator is working fine but the engine makes some little heavy sound and petrol consumption is to much and on gas its to good approx 220 km in one cylinder in local the mechanic suggests me that i should for its own carborator he has checked all the lines the connections are there for petrol the only thing he has to do is to fix the carborator and its air cleaner and the sensors it will cost round about 6k and you know its a one time cost.

[testdriver]

Dear test driver,

Assalm-o-alikum i have purchased a woo in a very low budget the machanic first checked the car its engine is in good condition but it needs some work round about 20k in which i have to do the wiring of ECM because the carborator installed in this car is nissan the engine is daewoo 1600cc and five forward gears now my car is on work shop for some starring work and wiring and also the other accessories like the carborator and its sensors and wiring now what you suggest the nissan carborator is working fine but the engine makes some little heavy sound and petrol consumption is to much and on gas its to good approx 220 km in one cylinder in local the mechanic suggests me that i should for its own carborator he has checked all the lines the connections are there for petrol the only thing he has to do is to fix the carborator and its air cleaner and the sensors it will cost round about 6k and you know its a one time cost.

Congrats for the purchase! Daewoo engine is 1500cc btw

If someone has installed a carburetor, he must have altered the intake manifold. If that's the case, just buy a complete kabli intake manifold with sensors. Is the ECM also removed? If yes, buy ECM with engine wiring.

[thanda]

@SALARSCAR
awsum work bro