Efi conversion any one did it in Pakistan? Ecotrons efi kit any good compared to carburetor?

[Hassan1991]

At least not for me

[qazi.junaid_pakwheel]

I am looking to take this idea commercial and to provide this as a viable option. Will like to talk to Margallar to get more details about this.

[asjdsm]

Not a viable option in Pakistan.

[newusernamenotfound]

Insert doctor strange meme Teach me

I want to do this to my GS150, an EFI system will really help in high alt. areas.

[margallar]

I think, if you have a passion for cars or bikes, Efi conversion is one of the most challenging, but rewarding things you can do to yourself

[asjdsm]

Budd you were doing such an experiment. Any share about that one?

[nfssaad]

what hardware did you use, where did you source the equipment?

[margallar]

Ecotrons efi kit. Experiment was on cd70 engine, which went really well.

I have a really shitty YBR125 engine and also a honda 125 engine (in import). One of those will be next. Last time i was involved a small bit in the tuning process. This time i will probably do it on my own.

its hard, you waste alot of fuel to get the V.E table right. but afterwards, you have a really cheap running engine with a button for performance. It does have altitude correction, idle control and warm up factors

[asjdsm]

Good. I have Piaggio with 200cc liquid cooled engine. 17nm/15hp. Using pz30 and brutal acceleration I get 35-40kmpl on long routes. Recent trips from islamabad to abbotabad to muzaffarabad to pir chanasi to murree to isb 380kms in only 9 ltr. That pigs its avg above 40kmpl.

Any ideo efi will bring any improvements in performance or fuel efficiency?

Never faced any engine heat up or altitude affect on engine performance.

[margallar]

EFi will give gains in both power and economy. BUT, it is not as easy as bolting the damn thing on the engine, it takes months to get it to run right. Also, it is very expensive. I don't remember the exact numbers, since i used it in university, but the equipment was upwards of 60k.

[nfssaad]

the ecotrons kit is about $600. add shipping and customs, and you will probably buy a new CD 70.

[khan.aamir]

AOA, can you please share how much it costed you in the end including custom duty. Was a bit confused on how much the duty could be.
Many thanks and kindest regards
Aamir

[muhammadwaqasanwar]

Hello I am an engineering student keen about Automobiles, I have spent major part of life studying and handling IC engines, I have spent almost a year performing an EFI conversion of a Basic 70cc Engine, it was difficult since it was'nt done on grass root levels, we had to go through a dyno tunning and we even used wide Band 02 sensor for getting results right, it went successful and we performed quiet well in an internatinal competetion representing Pakistan, Now I plan to convert my very own YBR 125cc to EFI and best tune it for Pakistani Riders, I have got another 125cc Honda planned after that, I am thinking about converting it into Startup, if you have any questions then contact me at my email muhammadwaqasanwar@me.ceme.edu.pk or Waqas 03215960678

[muhammadwaqasanwar]

go for cheap Chineese Kits they are basically the same as ecotrons just the interface is different

[muhammadwaqasanwar]

have you been to gilgit, carburettor bike fails at the heights of Babusar top

[husnalaiq786]

I have foud anothr fuel injectin kit
https://www.rollingwrenchdenver.com/products/diy-rolling-wrench-fuel-injection-kit?variant=8174662778997

But it is realy costly

[margallar]

The cheap way is to get an arduino based ecu from australia. I can make a wiring harness for it myself.

You can use sensors from local scrapyards and throttle body from china.

[asjdsm]

Yes in that case just order much leaner main jet, pilot jet, needle jets from aliexpress and you are good to gain more power

[margallar]

Sir, are you from isb?

[asjdsm]

Yes if they was intended for me l