Fast Daily Runner ( Khyber M13a)

Technical Forums

D.I.Y Projects

khyber

Tags: #<Tag:0x007fc2b2cfda38>

L3g3nd (L3g3nd) 2015-12-22 16:36:56 +0500 #61

Complete engine + gear + wirring + ecu was qouted for 70k. I got it from a half cut. Still haven't paid him yet.

Sent from my SM-N910C using Tapatalk

saboor73 (Saaboor A saad) 2015-12-22 16:52:05 +0500 #62

The oil line are a bit different in block to activate vvt vvt on m series and j series work like Toyota vvti it alters intake cam timing to over lap exhaust intake valve timing this creates low pressure area on top of cylinder which make cylinder exhaust fully so that more air and fuel burns to produce more torque

swift88 (swift88) 2015-12-30 05:43:25 +0500 #63

Updates ???

Sent from my iPhone using PW Forums

L3g3nd (L3g3nd) 2015-12-30 06:30:55 +0500 #64

@swift88
No progress up till now as the workshop has some repairs going on and i stopped the work because i have exams

Sent from my SM-N910C using Tapatalk

ehhaq (ehhaq) 2016-01-07 14:42:12 +0500 #65

Fingers crossed..

Damnation6 (Damnation6) 2016-01-07 17:08:10 +0500 #66

waiting for updates...

L3g3nd (L3g3nd) 2016-01-16 19:47:35 +0500 #67

Can some one please tell how to check all sensors and whether the wiring is cut or uncut?

SER_GTR (SER_GTR) 2016-01-17 12:30:06 +0500 #68

^^ Didn't You Check It Physically??? Its OBD-II Compatible...A Scanner Can Tell You Complete Story Of Sensor....!

Get OBD Port Working On It At 1st .....

L3g3nd (L3g3nd) 2016-01-17 12:54:06 +0500 #69

@ser_gtr
Actually the dashboard , the key switch, and some other things were at my home and i was busy with exams while the were doing wiring work . Yesterday i visited the workshop and they had the engine bay wiring laid out in order and the ecu connector was there the mechanic said that the ecu and scanners are in the lab and its closed now so tomorrow i have to visit again and they will connect it with dashboard internal wiring. I wanted to ask whether the wiring with each clip and insulation on is sure to be uncut ?

Sent from my SM-N910C using Tapatalk

SER_GTR (SER_GTR) 2016-01-17 14:39:57 +0500 #70

even if its wired...the working of sensors can be easily know when u put it on scanner....

L3g3nd (L3g3nd) 2016-01-17 14:53:45 +0500 #71

Yes i know but as i said the ecu and scanners were in lab and it was closed so i will check on monday. Although the workshops main work area is electronics.

Sent from my SM-N910C using Tapatalk

clicktosaad (clicktosaad) 2016-01-18 07:03:04 +0500 #72

looking forward for final picture

L3g3nd (L3g3nd) 2016-02-01 19:21:37 +0500 #73

I need to ask if anybody know that can i move ecu inside the dashboard or its not possible?

Sent from my SM-N910C using Tapatalk

L3g3nd (L3g3nd) 2016-02-07 07:01:56 +0500 #74

Wires wires so many wires.

Sent from my SM-N910C using Tapatalk

L3g3nd (L3g3nd) 2016-02-07 07:04:26 +0500 #75

Ecu and all the wire mess

Sent from my SM-N910C using Tapatalk

L3g3nd (L3g3nd) 2016-02-07 07:07:16 +0500 #76

Modified fuel tank for installing fuel pump.

The pump i found after searching for 7 hours as it was the only one which was fulfilled the requirements and was the height of the tank

Sent from my SM-N910C using Tapatalk

L3g3nd (L3g3nd) 2016-02-07 07:09:30 +0500 #77

The fuel pump installed in the tank using the genuine fitting and plate that came with it

Sent from my SM-N910C using Tapatalk

L3g3nd (L3g3nd) 2016-02-07 07:11:36 +0500 #78

Still haven't found the gear lever which can match the gear step and the cables which have sufficient length. Brought and changed 3 gear lever uptill now
Anybody can help ?

Sent from my SM-N910C using Tapatalk

SER_GTR (SER_GTR) 2016-02-07 08:52:33 +0500 #79

Ask Me And This Need To Be Sorted Before Swap Not After SWAP.....!

SER_GTR (SER_GTR) 2016-02-07 09:14:02 +0500 #80

Which Ones You Tried??? Did You Try Swift And Jimny Ones???? They Should FIT Or There's Cable LEngth Issue?