MA Audio HK1398 VS AudioBahn A2200HCT

[Lafafa]

i can understand why you liked the ratings. but do also keep other things in mind. for the price you can get so much better. and if you want to power up really high output subwoofers like the SPLs, than you should consider MONO amplifiers. they are more efficient. usually 75-90% efficient (depending on they type/brand/quality of the amp).

also remember, that this audiobahn will require a very strong powerful electrical system in your car. you can get same power out of a nice mono amp without putting too much load on your car's electrical system.

what do you want to connect to the amplifier??

[Lafafa]

some good amps u can look into:

Fusion NV-AM25001
NV-AM25001
825 Watts RMS x 1 Channel @ 4 Ohms and 1% THD+N
1310 Watts RMS x 1 Channel @ 2 Ohms and 1% THD+N
1790 Watts RMS x 1 Channel @ 1 Ohms and 1% THD+N

it has fuse of 200amp...it is quite underated and would give you more power than this.

NV-AM16001
NV-AM16001

the NV series is expensive...u can also check this out:
PP-AM20001
for rs19k
PP-AM20001

kenwood latest mono amp.. x11D is great too. rs24k. it is i believe 1200rms @ 2 ohms and @ 1 ohms.
KENWOOD | Car Entertainment 2009-2010

all the amps that i have told you are mono amplifiers - Class D.

and there are many many others out there....please dont waste money on 2ch amps...sure, if u turn bass boost and gain high on the audiobahn, it will indeed make life terrible for the SPLs...and probably burn or damage them due to excessive clipping

[enerlevel]

well i have fixed a spoilt 1600D and 2500D. the amount of stuff inside it shows tht it is a heavy amp. most ppl feel its not tht good is because it doesnt have any "bass boost db" function to it to give u tht "wow" factor. wat it runs is through its own power.

secondly MA audio and audiobahn both are also way over rated.check their subs u will know.2500rms for only $200. to good to be true.

now about the fusion nv25001. the inner circuit is not even half of wat u see in 2500D. but yes what it does have is the artificalbass boost function which makes u think its more powerfull.

now about x810D. if its digital amp , stay away!!!. if not , then to stay away:D once branded amps starts to give problems , its very very difficult to fix it.

[enerlevel]

HK1398, MA Audio HK1398, MA Audio Amplifiers, MA Audio 2 Channel Amplifers

if this is the same amp , where does it say 2 ohms stable mono??

[Lafafa]

yeah branded difficult to fix.

enerlevel....i tried finding the 1600D and the 2500D. no longer available anywhere....atleast i didnt find it in khi. do u know where i can get one??

[scorpion80]

now about x810D. if its digital amp , stay away!!!. if not , then to stay away:D once branded amps starts to give problems , its very very difficult to fix it.

agreed i had a bad experience with this amp ... within a year it starts tripping resulting me to sell it on a veryyyy cheap price to a shopkeeper... as i coud'nt able to fix it ..

[geforce]

1600 Watt 2 Channel Amplifier
400 watts x 2 chan. RMS @ 4 Ohms
700 watts x 2 chan. RMS @ 2 Ohms
1600 watts x 1 chan. RMS @ 4 Ohms
Thermal, Short & Overload Protection Circuitry
Platinum Plated Screw Type RCA Jacks
Double Sided Black Epoxy PCB Board
Variable High Pass & Low Pass Filters
Platinum Plated Block Terminals
Fully Regulated Power Supply
Stainless Steel Finish Heat sink
0-18dB Variable Bass Boost
Quiet Fan Cooling System
Full Mosfet Circuitry
2 Ohm Stereo Stable
THD: <0.05%
Signal to Noise: >90dB

[geforce]

According to ENERLEVEL`s webpage given
AMPS SPEC...
1600 Watt 2 Channel Amplifier
400 watts x 2 chan. RMS @ 4 Ohms
700 watts x 2 chan. RMS @ 2 Ohms
1600 watts x 1 chan. RMS @ 4 Ohms
Thermal, Short & Overload Protection Circuitry
Platinum Plated Screw Type RCA Jacks
Double Sided Black Epoxy PCB Board
Variable High Pass & Low Pass Filters
Platinum Plated Block Terminals
Fully Regulated Power Supply
Stainless Steel Finish Heat sink
0-18dB Variable Bass Boost
Quiet Fan Cooling System
Full Mosfet Circuitry
2 Ohm Stereo Stable
THD: <0.05%
Signal to Noise: >90dB

^^
the specification tells
this amp is only stable on 2 ohms per channel
it isnt stable below 4 ohms below bridge mode
if it was stable @ 2 ohms on bridge mode , that mean
each channel is stable at even 1 ohms

NOW ACCORDING to your specs
2 X 400W RMS @ 4-ohm Stereo
2 X 600W RMS @ 2-ohm Stereo their it was 2 x 700Wrms @ 2 ohms
1 X 1600W RMS @ 2-ohm Mono their it was 1600Wrms @ 4 ohms
Thermal, Short & Overload Protection Circuitry
Platinum Plated Screw Type RCA Jacks
Double Sided Black Epoxy PCB Board
Variable High Pass & Low Pass Filters
Platinum Plated Block Terminals
Fully Regulated Power Supply
Stainless Steel Finish Heat sink
0-18dB Variable Bass Boost
Quiet Fan Cooling System
Full Mosfet Circuitry
2 Ohm Stereo Stable
THD: <0.05%
Signal to Noise: >90dB

Better stay away from this amplifier

[farrukh555]

@saqib
Ma Audio is stable upto 2 ohm..checks specs

[farrukh555]

@saqib
Ma Audio is stable upto 2 ohm..checks specs

[enerlevel]

dude if saquibs specs were correct , then there would be one more rating which would show

2 X 400W RMS @ 4-ohm Stereo
2 X 600W RMS @ 2-ohm Stereo
1 X ......W RMS @ 4-Ohms Mono
1 X 1600W RMS @ 2-ohm Mono

now since ur specs doesnt show 4ohms mono , i assume tht 2 ohms is a missprint and it actually is 4-ohms Mono

[adilsafder]

contact me

[saqib84]

@thnx 2 all
idea of both the amp is droped...

[saqib84]

@lafafa
from where and how much fusion nv2500 i will get??
@enerlevel
actual rating of 2500D is around 1600 rms @ 1 ohm....and fusion nv2500 can also give beter rms power around 1800 @ 1 ohm as it is branded and little bit over rated but not as much as solid audio..

[saqib84]

@all
Any good MonO amp 4 sale??having actual rms 1500+ @ 1 OHM???

[saqib84]

@geforce
this all discusaion is around MA audio...what u said abut audio behn??

[geforce]

trust none if isnt certified by CEA

if you want power , there are and lots or amps avail
why they are not cea rating pass ,
cause WRMS power may be fake embosed
or it doesnt pass THD test
or their THD is more then CEA requirement

about
Audio Bahn , its better then MA
but thats not good idea for running woofer on 2ch amplifier

get MONO ,
Solid Audio Mono`s are good
they can bear less Ohms
that is really good

But i seriously only trust on CEA rated amps

[saqib84]

brother have any list or tell me few CEA certified amps and there availibilty and prics in ph having rms range btw 15oo to 2k.

[scorpion80]

i guess all amps of pioneer and kenwood are CEA certify along with some good branded amps ..

[geforce]

^^ YES
saqib do bit khwari , go to market and let me know amps which you like to buy
or get company , model#
google it deeply , check wheter these amps are CEA certified or not