Piaggio Vespa P150S 81' RestoMod

[capsat]

Doctor saheb please use protective paint for the undercarriage. I'd use bitumen coating or Berger Industrial coat

[dr.waqaskhan]

It is already coated with linex (polymer based coating used to save undercarriages of SUVS to prevent rust)
It was generously sprayed inside and out before painting and if need be will do again.
It looks weird because it has flecks of the basecoats and primer
Photo for reference

[dr.waqaskhan]

Update: Due to power shortage minimal progress was made but acquired the 12V stator plate and it's flywheel magnet

Old 6V one

Also got some vinyl fabric for the seat forgot to take it's picture.
MashAllah

[tjkhattak]

From where you got the 12 volts stator and flywheel as I am in need of one please.

[dr.waqaskhan]

Shahbaz Ustad sourced it for me! It’s an oem ducati one.

[dr.waqaskhan]

Update: Today, the front hub, shocks and the spindle was assembled and installed. Most of the bearings and small nitty gritties were replaced with brand new

Along with that some miscellaneous things were done like

Px black coloured back tail/mudguard

Center mat was installed

IA will be making more progress soon!

[dr.waqaskhan]

Today's update: Got alot of stuff done.
1. Installed the remaining floor trim, used the best quality ones, we used good quality rivets to hold everything down!

The final look MashAllah

2. Got the repaired kick back from the buffing expert

Looks great MashAllah

3. Handle bars needed some fixing so we got them retrimmed first and then installed them with their cable holding attachments and the handle grips MashAllah

4. This is how the seat is going to be it wasn't ready today but the upholstery guy crafted the top cover and the foam but he will fix it with soft foam tomorrow and finish it. We requested a pleated patter and this is what we have achieved. The seat was a bit of a hassle as we had to get a metal sheet cut to it's size and then we had to screw it on top as a base for attaching the foam and the vinyl. The screws were later replaced by bolts and nuts.

Well MashAllah alot of progress has been made today Allhamdolilah. I am not rushing as speeding up the process decreases the quality. With everyday passing we are getting closer and closer Allhamdolilah.

[dr.waqaskhan]

Update: We got the vespa running today MashAllah
I wish I could post it’s video here! Following things were done today.
1. Installed the newly painted flywheel, the stator plate and did the timing adjustment. Along with that bolted on the starting coil and plug wire and made the necessary connections.

2. Installed the dual tip exhaust and the clutch plate. MashAllah

Side view

3. Installed the fuel tank and there is a big rubber spacer beneath it

4. The seat is done. MashAllah
The craftsman damaged the paint at one spot and it pissed me off but hopefully the paint department will fix it and there are some flaws in the upholstery as well​

MashAllah!

[hamikhan]

Very good waiting!!!! For more

[burhanahmed1]

I hope this is not the final position for the exhaust pipes. Seem dangerous

[dr.waqaskhan]

How is it dangerous?

[dr.waqaskhan]

Update: iA it's near completion MashAllah

[burhanahmed1]

How is it dangerous?

It seems to be sticking out from the body a long way at an angle with a sharp edge.

[dr.waqaskhan]

The tips are blunted so they wont injure anyone plus they only stick out an inch....this is only for a single rider so i wont injure hopefully InshAllah
If it does will swap the whole setup
Thanks for the heads up

[dr.waqaskhan]

Update: Headlight along with it's wiring installed and other things such as battery(VOLTA 12V), rectifier(HONDA CG125) and charger/crossover(HONDA CG125) tucked in, will be installing other things as the day goes along. The results of the headlight are EXCEPTIONAL! I will do the same electrical mods to my VBB as well InshAllah.

MashAllah one step at a time! Installing the tyres

The main ignition and kill switch

Horns, meter, rear braking setup and rear tyre will be installed tomorrow InshAllah and hopefully will get the delivery of the scoot! I gave the rear light, handle top cover and engine side cowl to the ustad today. Only a few rubber seals and miscellaneous things left. The cafe seat will be fixed tomorrow hopefully as it needs some cosmetic adjustment, I am also thinking of buying an after market India made long seat....lets see what happens! Allhamdolilah for everything

[dr.waqaskhan]

Update: Rear wheel and brake installed MashAllah

Also added the meter, handle top cover, miscellaneous rubbers, rear tail light, battery and locks! Almost there MashAllah
1. The rear tail lamp. We used a rubber bezel around it for a neat look. MashAllah

Full lights on with brake pedal pressed!

Light without the brake pedal pressed, it has 3 leds for the number plate as well

2. Installed the rubber gromets for the lids and also installed the locks for the side panel and the handle

3. The OEM Meter in Km/h! Swapped the crystal and black bezel MashAllah. I might swap the needle for a better one

4. With the handle top cover and the side stand

5. The battery and its accessories! Used oem Honda parts from a cg125, tucked in the battery and insulated it with styrofoam but I wish that I had a proper plastic battery box

6. Installed the front nose

MASHALLAH MASHALLAH MASHALLAH! Allhamdolilah

[dr.waqaskhan]

Today's Update: Did the first test ride MashAllah! It went smooth Allhamdolilah
Apart from that did the following things for todays
1. Installed the flywheel cover, kick’s rubber and cylinder shied! Also fixed the rear mud guard with screws!

2. Installed a boot on top of the rear brake pedal (this is from a Suzuki Alto and goes on top of the gearbox) and also installed the paddle’s rubber

MashAllah

[dr.waqaskhan]

Allhamdolilah! Sums up the build
MashAllah MashAllah MashAllah

[hamikhan]

Wah G wah Kya baat hy G app nay tow mela he loot liya

[dr.waqaskhan]

MashAllah MashAllah MashAllah
I will turn my VBB into a head turner as well if Allah is willing InshAllah