Restoration of my Red Datsun 120y(Complete) (pics from pg. 5)

[haroon_faq]

dost kiya kerwa raha hai itni fit tu hai

[Bad_Cheetah]

dost kiya kerwa raha hai itni fit tu hai

sir ge agar apko lag raha hei kay baich raha hun..tou nahin nahin bohat fit hei mashAllah..esa nahin karun ga dont worry lol

[punk1]

RIMS DONT SUITE it

and needs drop

[HotEngine]

Nice

bigger wheels will suit it more bigger and fat

[HotEngine]

@Mods : Please put these cool images in starting of thread

new number plates

[Bad_Cheetah]

RIMS DONT SUITE it

and needs drop

these were the most decent rims in the whole of nilla gumbad..which were in a deep dish design, didnt want to go for flashy bling bling because that is just too common, spent 2 hours in summers finding these..punk1..please dont say it dont suit:P..they look great in reality..pics dont do justice..and ive been having these urges to get them sprayed according to the colour scheme of the car..fingers crossed.

and yes i agree to the fact that it needs a drop from the back..ive already lowered it quiet a bit, and the exhaust pipe scratches with the humps here that is why im a bit reluctant to get it dropped even more, but i will get it done a little more once i get some spare time..will keep you posted

[Bad_Cheetah]

Nice

bigger wheels will suit it more bigger and fat

ahh whenever someone says this i get heart broken all over again.
the car originally comes with a 114 pcd and hubs which could support 12 inch wheel size..(factory recommended)
but i am currently running it on 13inch wheels..ive got 2 spacers on each of the front tyres and one spacer in the rear tyres with nuts on the wheel hubs changed to a bigger size..getting 13 inch wheels on it was a great hastle, finding the right pcd in a 13 inch tyre was horrendous if you ask me..any bigger than this is out of the question on the stock axels without tampering with the safety issues..i had intended to change its rear axel to a mark2's but somehow i had dropped the plan at the moment until i am running its stock engine.
however there is one more genuine solution to it that i use a more thick profiel tyres at the rear currently i am running a 175 70 r13, but that would put on extra weight and extra load on the engine..and it may affect the driveability, that is why i am waiting to get the whole rear axel changed once the engine is swaped, and then i could put in bigger tyres.

[theboss]

why did you not chip in a new nissan egine of fuel inject the existing one with an aftermarket kit??

[Bad_Cheetah]

why did you not chip in a new nissan egine of fuel inject the existing one with an aftermarket kit??

mashAllah i bought a 1.8 ivtec therefore i had a strict budget for the engine swap in the datsun..inshAllah when i have enough spare money i will do the swap..until then i will run it on the stock A12!

[HotEngine]

@ Bad_Cheetah:

                       Oh i didnt knew that man

so the thing is its not made to be fitted with too wider wheels due to the original chases etc specs alright i understand its mechanical stuff hmmmm alright man

Anyways cool ride plus the interior mashAllah

[Bad_Cheetah]

@ Bad_Cheetah:

Oh i didnt knew that man

so the thing is its not made to be fitted with too wider wheels due to the original chases etc specs alright i understand its mechanical stuff hmmmm alright man

Anyways cool ride plus the interior mashAllah

thanks a lot buddy!

[Mady_Don]

gud one man.....

[Bad_Cheetah]

ty mady_don

[kashirafiq]

excellent paint job. i have a similar project in mind. datsun 120 Y or 1974 mark 2, 2 door with 1jzgte motor + some amazing paint job. anyways congrads. put some powerfull motor to make it a muscle car, right now it looks like a muscle car but goes like mule with original motor.

[Bad_Cheetah]

Thank you for the comments!
btw i doubt that a 120y would be able to handle all the heat from a 1jz..plus fitting it in the bay would be also a task..but if you think you can do it then go for it and keep us posted..there are only a very few 120y's left in good condition..
inshAllah when the time comes the swap would be done on this.
keep us posted on your project..best of luck!

[doppel91]

I'd love to have this kind of car. Right now I've Coure ECO 2008. I know if i sell it I'd get a good amount to get this type & also for denting painting & engine change. Can anybody pls advice me if its a good idea. I'm just in love with such classic cars.

[Bad_Cheetah]

I'd love to have this kind of car. Right now I've Coure ECO 2008. I know if i sell it I'd get a good amount to get this type & also for denting painting & engine change. Can anybody pls advice me if its a good idea. I'm just in love with such classic cars.

goodluck!
i hope you come up with an excellent project as well!

[rare]

@Bad_Cheetah
any upgrade in ur ride???

i found this thing for Stock A12 engine, no idea is it possible to build same kind of throttle bodies here . but do check it.

Thanks

[rare]

A-Series EFI: 4AGE Quad Throttle Bodies [Forum - Main Forum] : Datsun 1200 Club

[Bad_Cheetah]

@ sir no upgrades in this car, ive spent my money on car audio in my civic, maybe in the future, this engine is one of my favourite engines!
thank you a lot for your concern, i would definitely contact you for any further updates.