Self Tunning - Khyber G-10 (Plugs, valve clearance, spark gap etc)

[brownrose78]

Brothers,
Few days ago, my Electronic fuel pump went out of order so I went to mechanic for replacing fuel pump. On suggestions of pakwheelers here as well as got tired of noise Duug Duug of e-fuel pump so bought new mechanical fuel pump & gave to mechanic.

When mechanic opened old fuel pump (in front of me), he said Connecting Lever is not present in the old one. I went to spare parts shop & asked, he said that part does not comes in new so replaced mechanical with electronic one.

But as this electronic has no provision of Fuel return line so i am thinking of making mechanical fuel pump also operational, I have a plan to keep both pumps operational in parallel.

My question is that what that connecting lever & lever rod is called & from where can i find? If not found, can i use any other similar rod which might come in Mehran or old alto models? Please guide m.
That rod will be intact with the lever encircled in red below:

[shaidbokhari]

U have to get it made by any lathe shop if not available in market

[brownrose78]

During tuning, my mechanic changed to Iridium spark plugs of temperature grade (Heat Range) 5 with new Ultima 8 mm wires.

After 2-3 days, my petrol/cng cut-off switch blown up, when cng guy came, he told that it happened due to wrong spark plug (BPR5xxx) as grade 5(Heat range of 5) is considered too hot so better use, relatively colder plug than it as prescribed in user manual. So he returned my old plugs and put these spark plugs:

When i checked manual, heat range of 6 was recommended so can any body confirm, my mechanic is telling me right not to use hotter spark plug

What benefit will i get using colder spark plug?

[ali2cool]

hello fellows

does any one knows any good electrician (not juggari) for Khyber at township or johar town area who knows well to connect the connections (pipes) of Ac idle and Electric idle load solenoid properly
both are available in my Khyber and were working before a Carb tunning,seems like the mechanic messed with those pipes.
if any body have a picture of both of them in their Khyber, where they connected properly
Thanks

[shiekh123]

visit caregar restomods in johar town. you will feel yourself comfortable as he is quite professional.
he owns a khyber himself. he is into cars mods and restorations.

[brownrose78]

@ali2cool

[ali2cool]

okie bro you mean surkhail

[ali2cool]

thanks bro for sharing
i will try to figure it out according also

[margallar]

that guy was speaking garbage.

the spark plugs have nothing to do with the cng switch going bad.

the most they can do is cause some knocking (that too unlikely)

[brownrose78]

I also taught same way that there might be another reason. Coincidentally, he found 1 parameter out of spec. that wrong Heat range spark plugs were used so he put all Blaim over it.

Coincidentally, after that no such problems came so in follow-up visit he became more sure that Dekha Sir G, 1 h ghalat heat range ne kitna nuqsan kar diya ap ka.

BTW the thing that burnt was not cng switch but the Petrol cutout switch which is installed in line of petrol before going to fuel pump.

[ali2cool]

AOA
bro can i get a hint where exactly the red circled two hoses are connecting

[margallar]

that was most probably a short or just end of life for the part.

spark plug has nothing to do with it. the one he has installed is also no good, BP6ES / BP6EY are the perfect ones to get. or denso w20ex-u

[shiekh123]

you mean surkhail

yes absolutely. watch his videos on his Facebook page or on his youtube channel. he is quite professional

[ali2cool]

yeah bro i been watched his whole project khyber
will visit him for it

[brownrose78]

Assalamo Alaikum All,
Due to my busy schedule, could not pay attention to my Khyber, could not wash since last 4 months and even then daily running, just wipe the wind screen, put petrol and drive and 1 by 1, these damages occurred to my Khyber...

Bike hit from rear side broke genuine bumper

My road Sweeper was going in hurry and broke side mirror

Some thief stole away Number plate Light cover from my office parking

Also tried to open left one but could not open it due to rusty screws and left it loose which was tighten later

I saw in my nearby shops but could not find number plate lights cover and side mirror. Every shop suggested to install retractable side mirror of Cultus 2000-2016

What will be the cost of bumper, bumper clips, mud flap price these days? @omersiddiqui5482

I think recently, @mustansirbillahasada has sourced genuine bumper (Thailand or Taiwan made) in Karachi. From where you got these and price?

[omersiddiqui5482]

Not sure about the price these days... But all the things can be sources from one shop at plaza... The bumper would be taiwanese.

Call up Arif Bhai 0300-2265005, he will either have it taken out for you or will have it delivered...

[brownrose78]

Jazak Allah @omersiddiqui5482,
Talked with Arif Bhai and he told that he has no stock of imported parts for Khyber now.

He has only Local made parts in his stock .... Local Karachi made bumper, he quoted in Rs. 1,400 while for Locally Karachi made Side mirror (1 side) is costing Rs. 500.

I have concern about Quality....

[omersiddiqui5482]

Imported is becoming difficult these days... Shipping restrictions due to COVID.

[mustansir44]

I was looking for Taiwan made bonnet and fender for around 1 month or so. Was unable to find it at first but was able to find it in 1-2 shops after a lot of visits to different shops. I also bought Malaysian made front bumper, I think the quality is better.

[brownrose78]

Some results of negligence by denter in my Khyber has started emerging, recently I found that on keeping my foot, I noticed some unusual, uneven surface.

When I removed carpet, observed a Big hole​ part of Floor was broken and already fell somewhere else​

Anyways, guide me for surgical patching, do I have to put Floor part (Farsh) of driving side only? In what guage as I have forgotten which guage denter used that time.
@capsat @typeracer @omersiddiqui5482