Swaping QG15DE in B13

[aliam_786]

Burn....

That's Not A Good Word In Dictionary Of Cars With ECU.....! Be Careful....!! They Don't Come CHeap

but not by me.... elctration burned it ........ that was returned and original borsh maf is fitted in custom made housing......
and every thing working fine going to wire up meter and some other things.....

[aliam_786]

PM'ed you the contact number of relevant person.

thanks bro.... now every thing is ok now shall use it in future....

[shaheryar.khokhar]

bol with your project =)

[aliam_786]

@star2
bro the pin u told doesn't do any thing like flashing plz conferm and then tell me pin to check flash code....

[aliam_786]

@star2
plz conferm and post the pin to check flash codes...
and i connected fuel pump relay but pump is working continuously as car is switched on ecu stats giving negative to relay as i switch the car

[aliam_786]

fuel pump is fitted like this freely but giving issues in accelerating and breaking solve this problem when i get time to do...


old steering column


new one is fitted


Maf sensor i got is with pipe of big diameter so a custom pipe is made to fit maf and now working fine

[star2]

@star2
bro the pin u told doesn't do any thing like flashing plz conferm and then tell me pin to check flash code....

check the connections again....... you must be missing something....

[star2]

@aliam_786

You have to connect the # 21 pin to the LED in meter

Then

You have to give the # 111 Wire +12V and It will flash

[star2]

@aliam_786

yaar I told you how to put the pump. You have to tie it by making a little extension to the small pole which is right under your finger while you are holding the pump. You have to first make a measurement by putting in a welding wire for marking purpose to have an idea that how much you would need to extend that pole connected with the guage for its support.

[star2]

@aliam_786

bhai kahan reh gaya

[aliam_786]

@aliam_786

yaar I told you how to put the pump. You have to tie it by making a little extension to the small pole which is right under your finger while you are holding the pump. You have to first make a measurement by putting in a welding wire for marking purpose to have an idea that how much you would need to extend that pole connected with the guage for its support.

bro i tied that with tie clumps but hole of tank is too small then dono cheezain ander nai jati not i'll tie that after putting both in tank not getting time for that.........
rest thing of flash code is not cumming like this @atta4444 also told same pins but nothing happened
plz conferm me pin for k-line data communication......
i am having elm 372 usb type can it support nissan tested toyota,honda with that.....

[star2]

bro i tied that with tie clumps but hole of tank is too small then dono cheezain ander nai jati not i'll tie that after putting both in tank not getting time for that.........
rest thing of flash code is not cumming like this @atta4444 also told same pins but nothing happened
plz conferm me pin for k-line data communication......
i am having elm 372 usb type can it support nissan tested toyota,honda with that.....

Here you go:

Pin # 63 for KLINE

[aliam_786]

opened up tank and cleaned it @star2 what is that orange pipe purpose...


now tied pump with bettery rod and screw up with guage...

[aliam_786]

@star2
how can i wire up heat lights and fan blower
high beam and low have seprate wires should i use diodes....
pump was working continuously before starting bcoz electration connected starter motor's wire with switch
now problem is resolved with the help of @atta4444
i pressed all the grips of sensors and check light is gone.... nissan doesn't support elm 327...

[SER_GTR]

MASHA'ALLAH...Fuel Pump Aisa Lagaya Ha Jaise Kabhi Khulega He Nai

[star2]

@star2
how can i wire up heat lights and fan blower
high beam and low have seprate wires should i use diodes....
pump was working continuously before starting bcoz electration connected starter motor's wire with switch
now problem is resolved with the help of @atta4444
i pressed all the grips of sensors and check light is gone.... nissan doesn't support elm 327...

G for head lights, you are going to use diode between the high and low point (those 4 wires) and connect that to "Electric Load Signal" from ECU.

Good to see that check light is gone. Be sure to wire up a DLC3 grip and use scanner to see what's going on at your spare time.

[aliam_786]

MASHA'ALLAH...Fuel Pump Aisa Lagaya Ha Jaise Kabhi Khulega He Nai

nai pehlt oper wala nut open hoga then guage out and then pump bad mai nikly ga fit b aisy hi hota hai

[aliam_786]

G for head lights, you are going to use diode between the high and low point (those 4 wires) and connect that to "Electric Load Signal" from ECU.

Good to see that check light is gone. Be sure to wire up a DLC3 grip and use scanner to see what's going on at your spare time.

pins are 67 and 68 plz conferm that

[aliam_786]

and not getting dlc connector here trying to find one...

[star2]

pins are 67 and 68 plz conferm that

yes, 67 and 68.