Bosch High Performance Fans

[uiv]

Bosch high performance puller fans with custom made shroud.

• High rpms, silent design, ideal for high performance/turbo charged engines.
• Fans made in Germany/US, no problem, damage, trouble whatsoever.
• Custom made solid structure MS shroud, no vibration or compromise.
• Shroud made to fit 92-2002 Accord radiators, can be altered easily to work with most of the wide radiator designs.
• Installed once, for an hour of test run, that's it. No local use or abuse.

Fans came with original resistor to run at high/low speed.

Size:

17x27x3.5" All sizes, especially depth, can be easily adjusted according to specific requirements.

I'll throw in a very thick wired, high output relay/fuse box, to sweeten the deal.

(High output Starter motor and ABS relays, 60amp fuse)

Demand: 8,000

ONO
Contact: PM or email.

Disclaimer:

These are very high performance fans for high demands, they're quite power hungry and nosier than most of your cars at idle. So do your homework before any decision; I personally wouldn't install them with some car's stock 50-ish amp battery/generator setup.
I would only offer a spin-check at pick up. Delivery, installation, post installation, or painting them in some particular shade of pink wouldn't be on me.

Please call me for any questions or details.

[margallar]

Where do you get this stuff man

[uiv]

Where do you get this stuff man

Well to be unnecessarily honest, these fans are easily available in Bilal Gunj. You just need to look at the right place. It's somewhat difficult to buy one in use worthy condition though. You might need to browse through a pile of dozens to find one that'd suit you.

Prices start from as low as 1000-1500 for one, 2-3k for pair, but something like these in perfect condition may cost you twice as much. You need to pay very close attention to fan noise, blade wobble, motor spark strength, etc- else you'd be wasting your money.

[Xulfiqar]

Well to be unnecessarily honest, these fans are easily available in Bilal Gunj. You just need to look at the right place. It's somewhat difficult to buy one in use worthy condition though. You might need to browse through a pile of dozens to find one that'd suit you.

Prices start from as low as 1000-1500 for one, 2-3k for pair, but something like these in perfect condition may cost you twice as much. You need to pay very close attention to fan noise, blade wobble, motor spark strength, etc- else you'd be wasting your money.

You would have been really happy in Karachi then, I used to see OE - mini complete with shroud fan unit, OE ferrari exhausting fan units (the ones that scream like banshees). The best part IN PERFECT WORKING order.

same situation in buying though - you go through a 12 ft high pile to get one or two.

The cool part was when installed on a japanese car - and the banshee scream starts.

btw - painting them in pink along with some japanese font stickers (no matter if they translate to toilet) - will net you double your asking price.

[margallar]

Hmm...I will need to do some searching...for a spal fan

[uiv]

You would have been really happy in Karachi then, I used to see OE - mini complete with shroud fan unit, OE ferrari exhausting fan units (the ones that scream like banshees). The best part IN PERFECT WORKING order.
same situation in buying though - you go through a 12 ft high pile to get one or two.
The cool part was when installed on a japanese car - and the banshee scream starts.
btw - painting them in pink along with some japanese font stickers (no matter if they translate to toilet) - will net you double your asking price.

That's a nice idea: paint them in fagg0t pink pearl, some h0m0-kitty stickers, and a bumper sticker saying my fans have more torque than your VTEC... BAM instant riches.

It should be fun to see it on one of those JDM 660cc toasters. I think they'd create more thrust if installed at the back of it, then its puny engine.

I installed them on a CD Accord with an H23 and a Zeuna Starker exhaust ( @margallar : now where did I find that ), and they were louder than the engine at 100kmph.

[uiv]

Hmm...I will need to do some searching...for a spal fan

You won't be able to find SPAL. Settle for Bosch or Valeo, they're equally good for your car.
What do you need, puller or pusher? Single or pair?

[margallar]

Pusher for condenser....I will probably upgrade to a larger alternator....

Single

[uiv]

Pusher for condenser....I will probably upgrade to a larger alternator....

I've got one, Bosch, with original plastic shroud and resistor. Best thing is that it isn't fixed on shroud; you can unclip it and install like SPAL fan. Fancy it?

[margallar]

What are the dimensions?

[uiv]

What are the dimensions?

15x13x3" with shroud. 12" dia without shroud. I'll send you pics on whatsapp.

[margallar]

Hmm...I'll measure my setup to see if it might fit...will do it tomorrow

[azkhan]

Please share the dimension (height, widht and thickness) as Ive very litte clearance between radiator and engine

[uiv]

Please share the dimension (height, widht and thickness) as Ive very litte clearance between radiator and engine

17 x 27 x 3.5"

Depth can be decreased by half an inch. What's the car in question, and are you observing any specific problem, or just want a replacement?

[azkhan]

17 x 27 x 3.5"

Depth can be decreased by half and inch. What's the car in question, and are you observing any specific problem, or just want a replacement?

Well the machine in question is 1jzgte vvti single turbo swapped w124. No problems as such got Japanese single speed puller fans installed (the one with thinner motors) with thermo switch and no heating issues just thinking of replacing them with some high powered double speed siemens/bosch/spal fans whichever available.

So you say that the dimensions can be made to 17x27x2"?

[margallar]

i have only 10 inch space, so i will need to find a smaller fan.

[ahmadtariq]

@uiv I'm looking to get an AC installed in my ke70. The engine fan in the 4k engine switches on engine start and the car has some heating issues so I was wondering if there could be a better alternative to the current cooling setup, especially with the AC

[uiv]

Well the machine in question is 1jzgte vvti single turbo swapped w124. No problems as such got Japanese single speed puller fans installed (the one with thinner motors) with thermo switch and no heating issues just thinking of replacing them with some high powered double speed siemens/bosch/spal fans whichever available.
So you say that the dimensions can be made to 17x27x2"?

No, I meant half an inch or a bit more; say 2.8 inch.
If I were you I'd try to find original fan for that car, since it is a W124 and you can find Bosch in original fitting, and it's not giving any problems so you're not in a hurry.

i have only 10 inch space, so i will need to find a smaller fan.

That's a bugger. I'll think you'll find Japanese fans in this size, SPAL isn't available and I haven't seen many Bosch or Valeo in this small.

@uiv I'm looking to get an AC installed in my ke70. The engine fan in the 4k engine switches on engine start and the car has some heating issues so I was wondering if there could be a better alternative to the current cooling setup, especially with the AC

They won't fit in KE70. It'd be better to install one fan with bigger dia, something like old Merc W123 fan. You can try to find one of those in Bilal Gunj.

[ahmadtariq]

Will check it out, thanks

[azkhan]

Okay so ill try to find original bosch/siemens fans. btw my rad core size is 24x16inch and i can go for max 3 inch. Do you think ill be able to find electrical fan in this range. I think one HD puller fan would be producing more power than these two fans and it would be dual speed as well.