Charade 84-86 (G11) in 2022

abdulrehmanrauf (Abdul Rehman) 2022-02-16 10:42:09 +0500 #102

@syedfaizan1, Charade G11 (84-86) comes in 3 different sizes, 12, 13 n 14inches. 14 inches as per my knowledge came in Turbo variant. 12 was the starting size later they also came in 13. PCD is always 110. Try to find good enough condition steel rim (or alloys) (only of 110 PCD (never 100 or 114) of size 13 with 165 (recommended) or 175 tyre width. If you are going for alloys then if they are modified PCD or of 114 PCD then they are meant to be trouble.

abdulrehmanrauf (Abdul Rehman) 2022-02-16 10:46:52 +0500 #103

This is factory fitted 13 inches 110 PCD steel rims, tyre size 175 / 75.

This is 13 inches non-modified 110 PCD alloys with the same tyre as above.

nnabeel (nnabeel) 2022-02-16 18:24:36 +0500 #104

very rightly told by @abdulrehmanrauf.

try find the original stelies and get rid of these rims. or u want to look for original alloys that came with most of the charade detomasso comonly available in PK.

umair4a1 (umair4a1) 2022-02-16 19:33:57 +0500 #105

@Hassan1991
@nnabeel
And how are all of you Guys? Hope you all would be fine.
I like to discuss one thing. When i bought this car, it was with Corolla 86 carburetor (previous owner was really a Fraudia). Anyhow that carburetor was making trouble so on the recommendation of mechanic, i have installed Suzuki's mehran carburetor. Its running fine but I have serious doubt that it would not be good for over all engine. Also i have not seen any improvements in terms of milage.

So what you guys suggest? May i stick to it or change it with stock carburetor?

Looking for valuable response from you guys.

Best Regards:
UMAIR

helper_learner (helper_learner) 2022-02-16 19:55:36 +0500 #106

It is 1000cc where as mehran is not...

It might put some stress on engine...

But whether it put stress or not It is best to put original carburetor...

Hassan1991 (Electrical Engineer ) 2022-02-16 21:52:35 +0500 #107

ALLAH ka shukr
How are you?
Yes surely you should consider installing oem carburetor.
These carburetor swaps are useless.

umair4a1 (umair4a1) 2022-02-16 22:04:27 +0500 #108

@Hassan1991: Good to know about you . I am also fine by the grace of ALLAH

Alright. May be i will goto Peshawar on Saturday. Will try to search stock carb in decent condition. Wat things to check before buying a Kabli carb ?

Any tips or suggestions?

nfssaad (Saad Ahmed Khan) 2022-02-17 08:46:59 +0500 #109

original carburettor was a double barrel one if i remember correctly.

mehran etc are all single barrel...

there are many tiny parts in the carburettor. including the auto choke. normally auto choke does not work because its water passageways are corroded and choked... try to find one with no corrosion.

umair4a1 (umair4a1) 2022-02-17 09:00:36 +0500 #110

@nfssaad: Alright. Will keep that tip in my mind .

Regards

Hassan1991 (Electrical Engineer ) 2022-02-17 11:00:47 +0500 #111

Also if you are getting a kabli carby it's better to buy a new rebuild kit for it. If available.

umair4a1 (umair4a1) 2022-02-17 11:56:00 +0500 #112

@Hassan1991: Bhai. New rebuild kit means new carb or what? Sorry I didn't understand that.

Hassan1991 (Electrical Engineer ) 2022-02-17 12:29:49 +0500 #113

Like this.

umair4a1 (umair4a1) 2022-02-17 12:37:55 +0500 #114

@Hassan1991: ok Bhai. Got it. Will try my best to find that inshallah.
Regards:

umair4a1 (umair4a1) 2023-12-20 14:06:47 +0500 #115

Hi Guys: How are you All ? Hope you all would be fine. Specially Sir @Xulfiqar @Hassan1991 and all other Senior Members. Best wishes to all.

Now on the top My G-11 is running fine till date with the grace of Almighty with minor maintenance.

Need little bit guidance about the Exhaust/Muffler of my ride. It is rusted too much from the bottom, i dont know if its the stock one or changed by the previous owner. So Guys, what would be the best choice of the Exhaust ? any measurements to keep in mind when going to replace or it may be repair it ?

Thanks in advance.

Jazakallah.

UMAIR

Hassan1991 (Electrical Engineer ) 2023-12-20 21:22:42 +0500 #116

Hello. Glad to know.
You can buy a new one.

umair4a1 (umair4a1) 2023-12-20 23:43:56 +0500 #117

@Hassan1991.
Glad to see ur reply. Any local made standard exhaust will work fine or there is any specific size or measurements?
Regards:

Hassan1991 (Electrical Engineer ) 2023-12-21 01:39:08 +0500 #118

Get a good quality one.
Measure the inlet pipe diameter. It should be same as your exhaust pipe diameter.

umair4a1 (umair4a1) 2023-12-21 10:07:37 +0500 #119

@Hassan1991:
Thanks alot for prompt response. I will definitely keep that in mind inshallah.

Currently, did a temporary work (jugaaar) by myself with placing 1 rupee coin and small metal usually find in the box of mosquito coils to hold it with a magic glue. Here are pics ...... ️️️️️

Regards:

Hassan1991 (Electrical Engineer ) 2023-12-21 11:14:15 +0500 #120

Insha ALLAH
But this juggar wouldn't last due to heat.

umair4a1 (umair4a1) 2023-12-21 11:19:58 +0500 #121

@Hassan1991: Hahaha. True Bro. But its working fine on Low RPMs as the weather is extremely cold here in Kohat now a days, but it wont last longer thts for sure .

Waiting for the weekend. Inshallah will fix this and update here.

Take care
Regards: