CVT Start Clutch Calibration - The AUTEL Way

[Xulfiqar]

thanks for sharing
how much voltage and current to be applied to the coil?

EDIT:

Q2 - cotton as in the surgical cotton?

Q3 - where to get the heater / coil wire from?

the coil can be bought from a electrics shop selling commercial/residential stuff - if you notice paan ka khoka etc, they have a little board with this coil hanging from the side of the khoka with a bell push - its used to light ciggies.

Thats the coil you want.

[syncview]

the coil can be bought from a electrics shop selling commercial/residential stuff - if you notice paan ka khoka etc, they have a little board with this coil hanging from the side of the khoka with a bell push - its used to light ciggies.

Thats the coil you want.

that is great, thanks
I'll find out in the morning where to get that coil

[Xulfiqar]

sutta shop nearby?

[syncview]

yep lots of

[afnan.bashir]

thanks for sharing
how much voltage and current to be applied to the coil?

EDIT:

Q2 - cotton as in the surgical cotton?

Q3 - where to get the heater / coil wire from?

You would need 12 volts. Dont go for higher voltages as they may be lethal. In place of cotton you may try the thread for Dia or candel thread
@xulfiqar

sir you have one un answered question

[margallar]

the coil wala electric heater is also an option

[STUNNER]

Thats one good tool to have at home!

When you start charging, please give an appointment to my steermatic

[Xulfiqar]

You would need 12 volts. Dont go for higher voltages as they may be lethal. In place of cotton you may try the thread for Dia or candel thread
@Xulfiqar

sir you have one un answered question

Im into IT - as you guessed, aka IT mechanic. Work on sys and network side along with a lot of compliance work thrown in.

simple words = theykadaari.

btw -why baby oil in the smoker - why not desi ghee as used in diya - people will think you are cooking halva.

sheesha (huqqa) is also a good idea, the work may get sidetracked though.

[Xulfiqar]

Thats one good tool to have at home!

When you start charging, please give an appointment to my steermatic

That tool is damned expensive to buy for a home hobbyist.

[Xulfiqar]

deleted.

[afnan.bashir]

@xulfiqar pata lage sham ko @rustam54 ke neighbour naraz hote ho k desi ghe ka kalwa akele akele kha gae ho........

I have a question. While exploring the car i found the old ECU was still connected there under the passenger foot panel. That ECU was for F18A and was virtually useless. I pulled it off. No effect on car so far as i had already integrated other things like ELD or other to new ECU.

I noticed i had not connected Power Steering Pressure Switch. I have following questions

1. PSPW has two wires one RED and one BLACK. Which one goes to ECU? or both one for reference voltage or other for sense?
2. What are the logic levels needed to work. I mean when the switch is on Does it gives Positive 12 V or Ground Signal?
3. I figured out the wire from pressure switch goes to old ECU Grip, The RED one, I suppose if switch is powered by +12 volts then its source would also be from ECU? in other words both wires are connected to ECU.

Thanks

[galant1]

EDIT BY OP: QUOTE REMOVED TO REDUCE PAGE CLUTTER

@rustam54

Can you pm me from where you bought this scanner and what is the total price of scanner? I want to use it for my civic 2000 vti automatic.

Also tell me what about software either it has lifetime subscription or limited? What will happen if software subscription will expire?

[rustam54]

Thats one good tool to have at home!

When you start charging, please give an appointment to my steermatic

Well it will be limited complimentary service to old members. Drop me an email when you come by Lahore.

....................

btw -why baby oil in the smoker - why not desi ghee as used in diya - people will think you are cooking halva.

sheesha (huqqa) is also a good idea, the work may get sidetracked though.

What work?? :S

Ahhh Yes. The work!!!!.

@xulfiqar pata lage sham ko @rustam54 ke neighbour naraz hote ho k desi ghe ka kalwa akele akele kha gae ho........

...............

Afnan bhai, halway ka zikr nahin. Its a lot sensative issue for people like me (You'll understand when we meet )

@rustam54

Can you pm me from where you bought this scanner and what is the total price of scanner? I want to use it for my civic 2000 vti automatic.

Also tell me what about software either it has lifetime subscription or limited? What will happen if software subscription will expire?

Sir, Why do you want to use it on your civic?? Unless the requirement is some detailed problem analysis, the tool is beyond regular scope of a hobbyist.

[galant1]

@rustam54

For your information, I am engineer and I want this instrument for detailed analysis and for checking my automatic transmission because Honda scanner does not connect to automatic transmission whereas all thing are connected properly and shown in scanner. Also I don't want to pay couple of 1k at dealership for easy work. So please tell me following things:

Can you pm me from where you bought this scanner and what is the total price of scanner? I want to use it for my civic 2000 vti automatic.

Also tell me what about software either it has lifetime subscription or limited? What will happen if software subscription will expire?

[STUNNER]

Well it will be limited complimentary service to old members. Drop me an email when you come by Lahore.

I live in Lhr... actually I tried to note after viewing this thread if car vibrates much but I couldnt figure if its a yes or no.

@galant1
Im not sure what you mean by 'Honda scanner does not connect to automatic transmission' :S

The poster has shown reservations for disclosing price.

[rustam54]

@rustam54

For your information, I am engineer and I want this instrument for detailed analysis and for checking my automatic transmission because Honda scanner does not connect to automatic transmission whereas all thing are connected properly and shown in scanner. Also I don't want to pay couple of 1k at dealership for easy work. So please tell me following things:

Can you pm me from where you bought this scanner and what is the total price of scanner? I want to use it for my civic 2000 vti automatic.

Also tell me what about software either it has lifetime subscription or limited? What will happen if software subscription will expire?

Pm'ed you

I live in Lhr... actually I tried to note after viewing this thread if car vibrates much but I couldnt figure if its a yes or no.

.............

Your idle should appear to be same as in neutral when you engage D while pressing brake. If it is vibrating in N, then a TB check up or clean up can be done to prevent it.

There are other scenarios as well, which I am afraid i may not be able to explain on text.

[Xulfiqar]

@rustam54

For your information, I am engineer and I want this instrument for detailed analysis and for checking my automatic transmission because Honda scanner does not connect to automatic transmission whereas all thing are connected properly and shown in scanner. Also I don't want to pay couple of 1k at dealership for easy work. So please tell me following things:

Can you pm me from where you bought this scanner and what is the total price of scanner? I want to use it for my civic 2000 vti automatic.

Also tell me what about software either it has lifetime subscription or limited? What will happen if software subscription will expire?

your automatic transmission is hydraulic type with speed governor and throttle pressure cable - the two solenoids you see are for converter lock. I dont get what you want to achieve with this scan unit - To test your transmission you need the below item.

[galant1]

your automatic transmission is hydraulic type with speed governor and throttle pressure cable - the two solenoids you see are for converter lock. I dont get what you want to achieve with this scan unit - To test your transmission you need the below item.

@xulfiqar

I am want that scanner to check the codes of automatic transmission. I went to honda 3s dealership for checking transmission through computerized way.

They connected the scanner to ecu- all data was able to see at computer, no dtc, all PGMFI parameters are according to factory values but they click the AT option for checking the faulty codes for automatic transmission, the scanner is not connected to automatic portion to check the faulty codes. They said connection is not establish and hence we couldn't able to see the any faulty code.

That's why I need that tool also I am planning to upgrade the car to some latest model.

Can you tell me why their scanner is not connect to AT portion?

[Xulfiqar]

Hmm

Did they really try to test the AT from their tool?

Sounds like they were trying to con some money. Thev transmission in your car is hydraulic meaning there is no electric control. How do you expect this to scan something that's non existant.

The transmission is pressure tested from various ports which are for the various clutches and control pressure. It shifts from pressure differential between the speed governor and throttle cable.

The honda prosmatic can be interrogated . Yours is not prosmatec.

[galant1]

Hmm

Did they really try to test the AT from their tool?

Sounds like they were trying to con some money. Thev transmission in your car is hydraulic meaning there is no electric control. How do you expect this to scan something that's non existant.

The transmission is pressure tested from various ports which are for the various clutches and control pressure. It shifts from pressure differential between the speed governor and throttle cable.

The honda prosmatic can be interrogated . Yours is not prosmatec.

@xulfiqar

Yes they try to check transmission from their tool. I was standing in front of them and I checked two 3s dealership-same problem occurred.

Yes you are right that transmission in my car is hydraulic then 2 question arises in my mind that are:

1. How shifting is taking place and controlled if ecu is not controlled the shifting process?
2. How can we get dtc or faulty codes to check any problem in transmission for my car?