DIY Restoring Wiring Of B13

aliam_786 (aliam_786) 2013-12-06 12:21:08 +0500 #1

Just started this project to open the dashboard and repair the wiring in original shape and make all components working.

aliam_786 (aliam_786) 2013-12-06 12:28:27 +0500 #2

@star2
there are wires from seat belts but no warning light in meter.

Xulfiqar (Xulfiqar) 2013-12-06 12:48:19 +0500 #3

nissans are usually prewired for many things.

ZEE82 (ZEE82) 2013-12-07 14:38:34 +0500 #4

those wires for seat belts in B13 edition are not for WARNING light purpose but infact it trigers the galvanized coil type thingy inside the seat belt recoil setup which help in better and proper locking of the seat belt during jerks.

aliam_786 (aliam_786) 2013-12-07 17:46:26 +0500 #5

@zee82
Thah is not connected with that. no current in wires connected with that galvanized coil.

aliam_786 (aliam_786) 2013-12-07 18:04:09 +0500 #6

aliam_786 (aliam_786) 2013-12-07 18:04:10 +0500 #7

aliam_786 (aliam_786) 2013-12-07 18:04:11 +0500 #8

aliam_786 (aliam_786) 2013-12-07 18:04:12 +0500 #9

aliam_786 (aliam_786) 2013-12-07 18:04:13 +0500 #10

[ATTACH=CONFIG]1315796[/ATTACH]

aliam_786 (aliam_786) 2013-12-07 18:04:14 +0500 #11

aliam_786 (aliam_786) 2013-12-07 18:04:15 +0500 #12

aliam_786 (aliam_786) 2013-12-07 18:04:16 +0500 #13

ZEE82 (ZEE82) 2013-12-08 10:45:45 +0500 #14

look.the galvanized recoil setup of seat belt ill have a 2 wired grip, which will in return connect to the seat belt key locking sockit. find it and connect it straight away.also ensure that the wires u connect shudnt be lying cut through the line anywhere

ZEE82 (ZEE82) 2013-12-08 10:47:33 +0500 #15

the wiring is in its worst form. what i recomend is that if u have ur factory fitted central lock setup in ur doors, then remove the universal remote /keyless entry setup wiring from ur car asap

aliam_786 (aliam_786) 2013-12-09 12:16:59 +0500 #16

I had repaired all the wiring and this loom is taped well after changing burnt wires then i again install the keyless entry system.

aliam_786 (aliam_786) 2013-12-09 12:39:16 +0500 #17

I had repaired all the wiring and this loom is taped well after changing burnt wires then i again install the keyless entry system.

star2 (star2) 2013-12-09 15:06:04 +0500 #18

wah g wah

IsbCap (IsbCap) 2013-12-10 04:00:13 +0500 #19

It would be good if you provide some description and actual wiring process, rather than posting pictures of cats and a thousand wires

aliam_786 (aliam_786) 2013-12-10 09:57:52 +0500 #20

first of all i removed the whole dash board then removed the original taping on loom.After that i tried to find out burnt wires then i replaced those damaged wires which was causing problem like when i on parking light fuel needle start rising.But after replacing wire every thing was working fine.I taped the wiring loom and then fitted dash
Then I place led strips in AC panel and meter