G10 Carby to G10 EFI

Tags: #<Tag:0x007f95f8a0d468>

shamail_haider (shamail_haider) 2014-07-04 22:01:34 +0500 #1

AOA Respected Pakwheelers,
Hope you are all doing well.
By some chance, I've managed to get a G10 EFI engine with complete gear, ECU and wiring. I got this engine as a gift from a friend who swapped his Cultus with G15B.
I'm planning to swap my 3 cylinder motor with this 4 cylinder one. Just need a few details as mentioned below:

1) Will the engine be sitting on the same mounts?
2) Do the axles or Goddas required to be changed?
3) Will the car run trouble free after swap?
4) What things should be keep in mind during the swap?
5) What should be the swap cost?

Calling all the experts especially Mr.Xulfiqar.

P.S. The original picture of that engine and the Engine bay of my cultus are attached.

Regards,
Syed Shumail Naqvi

Sent from my A60 using PW Forums mobile app

shamail_haider (shamail_haider) 2014-07-05 22:58:25 +0500 #2

Where are all the cultus experts?

Sent from my A60 using PW Forums mobile app

meh1 (meh1) 2014-07-06 00:37:27 +0500 #3

in past EFi and carby versions of engines came because of emission requirements in some countries. they only differ in fuel supply. rest all is same.
1-yes same mounts
2-same axles will work
3- if all is done properly
4- see that no jugars are done. everything is done proper way. give special attention to wiring. better find silicone tape and shrink tubes. solder joints and cover with shrink tubes.
5- 15K almost

shamail_haider (shamail_haider) 2014-07-06 14:27:59 +0500 #4

Thanks a lot.
Yes, fuel supply is different but we can't neglect the power of 4 cylinder EFI as compare to 3 cylinder carby. And obviously I'm going to do this for the same of some extra power and fuel economy also.

Sent from my A60 using PW Forums mobile app

shamail_haider (shamail_haider) 2014-07-06 14:29:35 +0500 #5

My mechanic says "bhai 1 side ka godda change krna paray ga aur 15000 tak total cost aye gi including electrician work".

Sent from my A60 using PW Forums mobile app

umarkhan1 (umarkhan1) 2014-07-06 16:12:47 +0500 #6

Bolt on swap

Sent from my iPhone using PW Forums

umarkhan1 (umarkhan1) 2014-07-06 16:13:24 +0500 #7

Make sure that the electrician also wires up the CEL

Sent from my iPhone using PW Forums

shamail_haider (shamail_haider) 2014-07-09 02:46:10 +0500 #8

@umarkhan1
And CEL stands for what ?

Sent from my A60 using PW Forums mobile app

meh1 (meh1) 2014-07-09 02:53:24 +0500 #9

CEL=check engine light.

afnan.bashir (afnan.bashir) 2014-07-09 13:27:46 +0500 #10

Sana enjoy it?
Complete wiring
Solder the joints and shrink sleve no jugars
You may need to add evaporation canister to avoid fuel smell after efi conversion

Sent from my HTC One using PW Forums mobile app

shamail_haider (shamail_haider) 2014-07-09 13:45:36 +0500 #11

Please elaborate the following points.
" Solder the joints and shrink sleve"
" to add evaporation canister to avoid fuel smell after efi conversion"

Regards,

Sent from my A60 using PW Forums mobile app

afnan.bashir (afnan.bashir) 2014-07-09 14:03:12 +0500 #12

ECU needs noise free signals. Make sure all joints are soldered and instead of bijli tape secure them with shrink sleeve.

When you install fuel pump in tank huge amount of fuel leaves tank. Most tanks have two way valve to avoid vacuum and excessive pressure due to evaporation.Also these gets evaporated you want these vapours collected in canister and to be used for later use. Google it I am feeling sleepy rite now

Sent from my HTC One using PW Forums mobile app

shamail_haider (shamail_haider) 2014-07-09 14:04:21 +0500 #13

Thanks a lot. I'll surely Google it.

Sent from my A60 using PW Forums mobile app

Xulfiqar (Xulfiqar) 2014-07-09 14:07:50 +0500 #14

please check this first

https://www.pakwheels.com/forums/engine-transmission-powertrain/234712-want-buy-engine-swapped-car-want-swap-engine-think-again-2

umarkhan1 (umarkhan1) 2014-07-09 14:25:15 +0500 #15

@afnan.bashir
Ek kam ha ap se...
And i am sure you will help me

Sent from my iPhone using PW Forums

margallar (margallar) 2014-07-09 14:33:11 +0500 #16

How will you dispose that carby engine?

shamail_haider (shamail_haider) 2014-07-09 14:43:49 +0500 #17

Disposing of the carby? I didn't get you bro.

Sent from my A60 using PW Forums mobile app

shamail_haider (shamail_haider) 2014-07-09 14:44:25 +0500 #18

Thanks @xulfiqar bhai

Sent from my A60 using PW Forums mobile app

margallar (margallar) 2014-07-09 14:44:51 +0500 #19

Matlab will you keep the old engine with you after the swap or sell it somewhere?

shamail_haider (shamail_haider) 2014-07-09 14:53:08 +0500 #20

I'll surely keep it with me. No intentions of selling it because this engine is still healthy having no issues at all. I'll swap it back whenever I'll plan to sell my car inshaAllah.

Sent from my A60 using PW Forums mobile app