Little DIYs for My Khyber

[libra3]

like the work. good ride. the spray is Rs.110 in Islamabad

[dr3vil]

nice diys surely keeps cars looking new i did same thing with my cars radiator
and u sprayed the pulg wire with black spray
i suggest change them if their condition is bad get a new set of ultima wires

[Xulfiqar]

Xulfiqak bhai do you mean that black sold thing ? Is it capacitor?
Which one i should look for In desi terminology? and secondly will anyone will fit??

Thanks

The square black thing that is mounted to the coil and ignitor assembly with one bolt.

[wasay_ahmed]

nice diys

[bluespark]

The square black thing that is mounted to the coil and ignitor assembly with one bolt.

oh yes I got it. What is its function. ? Its missing wire since ages!

[bluespark]

nice diys surely keeps cars looking new i did same thing with my cars radiator
and u sprayed the pulg wire with black spray
i suggest change them if their condition is bad get a new set of ultima wires

dear wires are Ok. only one had faded portion so it was painted.

[speedster_101]

Ash tray looking nice after spray.

[Xulfiqar]

oh yes I got it. What is its function. ? Its missing wire since ages!

to suppress noise as the pulse generator in your distributor is quite noisy (electronically) and can cause radio interference.

[margallar]

dear I use cosmic leather polish. Is it good enough??

its just ok, not too good. armor all is gud. u can get it from metro

[bluespark]

to suppress noise as the pulse generator in your distributor is quite noisy (electronically) and can cause radio interference.

guide me about wiring of capacitor, I will DIY it!

[Xulfiqar]

get a non polar 0.47u capacitor - one end should be 12V switched positive and one end should be grounded on the distributor housing itself.

[bluespark]

get a non polar 0.47u capacitor - one end should be 12V switched positive and one end should be grounded on the distributor housing itself.

ok sir Thankyou will do it! and post pix here.

[smartdevil_striker]

Nice Work bro...

[mehrozniazi1]

nicely done ...loving it ..........dont paint wires..better get 1..and keep them clean

[bluespark]

nicely done ...loving it ..........dont paint wires..better get 1..and keep them clean

from where I can get genuine plug wires for my khyber in Pindi ? which brand to go for?

[bluespark]

The left rear light was dim and has its brake light bulb fused. My brother open it , cleaned it and replaced the bulb. Working great:)

BTW. the T-shape tool is his invention. The light screws are behind the cylinder, so no available tool can reach to them from any possible direction. However the mere clearance of 3-4 cm is available, and this T-Tool works like charm!!

[Xulfiqar]

for improved brightness - you should add the corner marker lights too in the brake lenses too, the socket mould is there but plugged. Cut the slot and put a new socket in there with a 5W bulb, wire it to parking lights - job done.

[daniyalahmad]

Years ago the ashtray of my car was in a similar position.
I removed it with the intent of painting it but I was too lazy.
I lost it somewhere in the garage and had to buy a new one.

[daniyalahmad]

for improved brightness - you should add the corner marker lights too in the brake lenses too, the socket mould is there but plugged. Cut the slot and put a new socket in there with a 5W bulb, wire it to parking lights - job done.

Sounds cool.
I'll try to do it.
In this car even with the brake lights on, there is less light on corners.

[Xulfiqar]

if you can - then paint the insides of the reflector dome white - its usually black in khyber (I dont know why thought) - it will make the lights shine brighter