Sunny B14 project

[Ghuncha]

Baki NISSAN ke ECU and wiring is hell different from others......!! a bit on harder side....!!
i did many toyota's and Now NISSAN's........its quiet on difficult side.....!!!
ECU's are also hard to identify

yeah you are right on both points.

@ghuncha...!
fortunetly yes....infact loom and ECC Box lying underneath my computer table and will get my attention once i am done with exams
found the wiring pin out too....and i also did some work on it earlier......traced wires......!! have to complete loom just....
Will share pics when i got it done.....

the manual s of which car/region?

[Ghuncha]

now the mounting of the ECU, the auxiliary control unit was mounted on a plate with four screws, which had a cover on top(plastic), the new ecu didnt had any mounting holes, only two bracket type things, so we improvized and came up with the following solution, now this plate(with ECU) sits neatly underneath the dash, and cover on top

[spectra]

now the mounting of the ECU, the auxiliary control unit was mounted on a plate with four screws, which had a cover on top(plastic), the new ecu didnt had any mounting holes, only two bracket type things, so we improvized and came up with the following solution, now this plate(with ECU) sits neatly underneath the dash, and cover on top

This was sameer's idea and i got it excuted from Paa Kharadiya

[onlyfaith]

nice work yar!

[SER_GTR]

yeah you are right on both points.

the manual s of which car/region?

JAPAN....wiring Matched

[SER_GTR]

U have the pinouts for GA15DE?

Paaje Dekhne parege....Shayad GA16DE ke hoge....!!!

[TEMPORARY]

Will this help

[TEMPORARY]

And this.............

[Ghuncha]

And this.............

hey thanks for the help though these diagrams are from the newer generation usa market drive by wire variant of this engine.

[xain]

@Guncha Good Going. So when are we going for the treat.

[spectra]

@Guncha Good Going. So when are we going for the treat.

We got it yesterday

He is currently sorting out the rpm signals issue because meter is for GA engine which has a distributor and this engine is distributorless so some emulator needed to let ecu think that "Aal izz wel......Aal izz wel......" and send rpm signal to meter in compatible format

[akifjanjua]

Tamaaan EFi gaarion ki wiring aglay haftay tasali baksh kar de jaati hai

with special notes "aal iz well" & "kuch nai hota"

[autophile]

@Ghuncha. Nice engine swap and DIY description. You did hell lot of a job. Happy driving

[imranbhatti]

@Ghuncha

Nicely Done (Y) & best of Luck with QG18 DE

[usarwar]

usman here.... dud is it a bolt-on on a B-13??
the 1991 model?

[spectra]

usman here.... dud is it a bolt-on on a B-13??
the 1991 model?

One mount will require grinding and resizing.

[SER_GTR]

@Nashi....! Crank sensor wagera se RPM signal nai generate horahe???

[SER_GTR]

One mount will require grinding and resizing.

GA Series Will Be A Perfect Fit Almost with No Alters....Just Mountings Change..!!

[qwertypoiu]

Some high tech DIY.

[Ghuncha]

@Nashi....! Crank sensor wagera se RPM signal nai generate horahe???

yar car which had this engine(nissan expert) didn't had rpm meter, but rpm signal is going to the auto transmission, i took that, that's a switch to ground signal for every spark, than modified the rpm meter, which runs of the coil/distributor, and alhamdulillah it worked, just installed it. following are the videos and pics of the process.

//youtu.be/http://www.youtube.com/watch?v=-KV02MTtcvE

//youtu.be/http://www.youtube.com/watch?v=iBd1gm6Ajco