Toyota Corolla Model (E-120) 2002--2008 Owner's and Fan Club

[mohsin-212]

And how to install torque pro as there is no free version available on Play store I only found torque lite

[hasankhurshid29]

And how to install torque pro as there is no free version available on Play store I only found torque lite

https://apkmos.com/torque-pro-obd-2-car-1-8-205-apk/

Try this

[mohsin-212]

And to install the pro profile??

[hasankhurshid29]

And to install the pro profile??

You don't need to install any profile
But you have to set it by yourself

[pwuser151957765694]

Is this obd2 scanner works on 2003 se saloon 3zzfe?

Can this obd2 scanner erase all the faulty codes and errors?

And can this obd2 scanner reset the ecu,and also relearn the iddling value?

[hasankhurshid29]

Is this obd2 scanner works on 2003 se saloon 3zzfe?

Can this obd2 scanner erase all the faulty codes and errors?

And can this obd2 scanner reset the ecu,and also relearn the iddling value?

Yes I am using on this same model and it can erase error codes

Don't know about ecu reset or relearning idle. I think for reset you can remove battery terminal

[naveedyu]

Yes. Same issue with me. Car pulls towards left at 50-60 kph. I will get all the breaks serviced and check for piston jam. Let's see it resolves. One thing merit attention. My car is fitted with CNG and spacers with 15 inch tyres. I think due to change in height it's center of gravity has changed and car pulls after applying hard breaks.
What about your???

[naveedyu]

Yes. I tried in GLI 2008 and obd 2 works fine. Valve starts opening at 82 and coolant temperature starts getting down before reaching 90. It goes till 84 and start rising again till 97 degrees. Immediately fan starts and temperature drops till 90 and fan stops. And cycle goes on like this.
These reading are from OBD II scanner

[naveedyu]

Yes. It shows real time coolant temperature

[mohsin-212]

Your Gli 2008 Gli is of new shape or same dumba shape??

[naveedyu]

Same dumba shape.

[mohsin-212]

@naveedyu @hasankhurshid29 can this OBD2 scanner be left connected during normal driving to check car's behavior during different conditions or it has to be removed after checking desired values .

[hasankhurshid29]

In my car it is always connected
I only disconnect it when i know I will not drive for few days to avoid battery drainage
Else no problem if its remain connected

[def3nder]

yes i have done once my one rear right light.

[def3nder]

mine is petrol and spacer of approx one inch in the rear wheel. i hate spacers as it left the car from rear and it doesnt look cool too, but i have no other option than spacers. Do your brakes service and give us our feedback.

[mohsin-212]

Glad to hear that now I will let it connected and activate high temp alarm etc in torque app as I no more rely on that dumb temp guage

[naveedyu]

It only consume very less current and no harm to let it connected if you use car daily. But for longer period i.e. a week or two, then it's better to remove it

[manobilla16]

my ELM does not work on my altis 1.8 however no issue with 2nz and L13A, upon connecting to Altis ABS lights starts blinking.... any work around to this

Also using 10W40 and planning to switch to 5w40.... what is your opinion and recommendation.. currently using Kixx.

very cold these days in Lahore and planning to swicth so far no issues with current oil but think in this cold wear may occur on initial cranking.

[hasankhurshid29]

my ELM does not work on my altis 1.8 however no issue with 2nz and L13A, upon connecting to Altis ABS lights starts blinking.... any work around to this

Also using 10W40 and planning to switch to 5w40.... what is your opinion and recommendation.. currently using Kixx.

very cold these days in Lahore and planning to swicth so far no issues with current oil but think in this cold wear may occur on initial cranking.

You have to add these strings in vehicle profile:

ATIB96\nATIIA13\nATSH8113F1\nATSP4\nATSW00

[waqar19]

Correct way of removing air from system. Start the engine and remove radiator cap. When thermostat valve opens, air will bubble out as shown in pictures. Keep adding water/coolant untill radiator fan kicks in.
Finally give few good revs and put the radiator cap back.

.
.
.