Nissan B13 Restoration

[star2]

For QG18, you may also need to replace the CV joints (Godday) and related stuff, if you go with the default gearbox of QG18. Fitting QG15 gearbox is a different story.

Not sure about the CVT transmission modification requirements, though.

alright
@spectra

Do we use rods for B13 and outers and inners of N16 with qG18??? axles ? Can you tell me what will be the changes we need

[spectra]

QG13, 15 and 18 share same manual gearbox (different ratios offered for all engines) and axles can be used from N16 in B14. Not sure about B13. Better check with Bilalahm. And have no idea about auto. Measure the lengths and see what fits. Do not try and swap rods, inners and outers. Get kabli full assemblies.

[star2]

QG13, 15 and 18 share same manual gearbox (different ratios offered for all engines) and axles can be used from N16 in B14. Not sure about B13. Better check with Bilalahm. And have no idea about auto. Measure the lengths and see what fits. Do not try and swap rods, inners and outers. Get kabli full assemblies.

understood, though I think the hubs of N16 and B13 have a difference and so will be the outers different, anyways, I will see this and update about them. I think complete assemblies of N16 axles have quite an amount to them, let's see....

[spectra]

U should start focusing on similiaroties first. Negativity is already in abundance around you and inside your head That way u will find a good solution to any problem being faced during the restoration of this peepa.

[star2]

U should start focusing on similiaroties first. Negativity is already in abundance around you and inside your head That way u will find a good solution to any problem being faced during the restoration of this peepa.

Here you starts again. I have explained similarities of axles, though will check it up closely. By the way, axles for auto and manual are different ? or are there any differences between the auto and manual gear positioning in placement for axles ?

[spectra]

Uncle as i said earlier. No iidea about auto. Theyy can be similiar or u might nneed smaller excel from a diesel version (shorter). But that is my guess.

[ZEE82]

Mustafeez bhai U ill need to upgrade the suspension(mainly axels) from b13 to b14 version axels, otherwise the QG18de ill throw away its factory fitted axles

[star2]

Mustafeez bhai U ill need to upgrade the suspension(mainly axels) from b13 to b14 version axels, otherwise the QG18de ill throw away its factory fitted axles

Hmm.... that's sad to hear lol

Thanks for the info brother.

[SER_GTR]

The Only Way To Know What Fits Best Is After You Get QG18 Inside.....!!

Hubs Axles Whatever......After Motor Is Place And Aligned In Bay.....!!

[syncview]

The Only Know To Know What Fits Best Is After You Get QG18 Inside.....!!

Hubs Axles Whatever......After Motor Is Place And Aligned In Bay.....!!

The truth has been said.

[star2]

unfortunately due to busy schedule could not go to the workshop today, but talked with my mechanic over the phone, he said your brake pipes are all over the engine bay and those are because of the brake T to which the pipes are coming and then going forward to tank. He said the T needs to be changed as it is not the original T. Rest, he has removed all the parts from the engine bay and inspected suspension parts. Now tomorrow, denter will take a final look at the engine bay and it will go for paint. Will go to workshop tomorrow.

[hamza91]

Nice going sir

[Xulfiqar]

unfortunately due to busy schedule could not go to the workshop today, but talked with my mechanic over the phone, he said your brake pipes are all over the engine bay and those are because of the brake T to which the pipes are coming and then going forward to tank. He said the T needs to be changed as it is not the original T. Rest, he has removed all the parts from the engine bay and inspected suspension parts. Now tomorrow, denter will take a final look at the engine bay and it will go for paint. Will go to workshop tomorrow.

Get those pipes galvanized. They look real sharp - almost give a new car look.

[Xulfiqar]

Brake pads are new and OEM replacement from Nissan authorized dealer, as well as rotors as I told you before. Two front brake pipes were replaced recently, one was leak, one had cracks but not leaked so both changed and they are good. Rear brake pads changed as well, about cylinders, not sure, if they needed to be replaced, will replace them if I find them new.

Regarding shocks, original oil filled shocks of B13 were recently placed along with original springs. Will see if they do justice, they are new practically, so hoping they do the trick else another 8-10k

was the brake fluid flushed out or simply bled and topped up, old watered brake fluid is useless for any sort of braking.

[star2]

was the brake fluid flushed out or simply bled and topped up, old watered brake fluid is useless for any sort of braking.

I am sure it is flushed out now completely.

By the way, some of the pipes are not of its own and I am having a great difficulty finding genuine brake pipes of steel from here. Neither the dealers nor the kabarias have it. They said everybody buy a used steel pipe of any car and your mechanic fits it like that. Then I ask them that what is the use of that "tikki" which is fixed with the wall to hold that pipes in a good alignment? and they look as if i am alien

[star2]

now my question is how to sort this issue when the brake pipes coming from booster are not original and not aligning proper with the body of the booster as well as wall. Mechanic seems in strangle If I ask him to align all those pipes so that they look nice and fitted on the wall.

Another thing, are there any brand new piping for this purpose available which can be molded so that we can make our own bends and copies of original housing ?

[IsbCap]

^^^ Good attention to details. And guess what..... bringing this 20-22 years oldie to stock condition is a mountainous task

[star2]

The picture is quite dark, but you can still notice the brake pipes out of control going right left to wall and not straight....

[star2]

These are not the original pipes altogether.

Are there mold-able pipes available which can be custom molded ?

[bass.lover1]

why u dun go for honda d-15 ?